-
ballvessel5 zveřejnil aktualizaci před 5 měsíců, 4 týdny
Replace Lock on Your UPVC Door Yourself
You can change the lock on your door made of upvc yourself, provided that you have full access to both sides of the faceplate. You’ll need a screwdriver and a long bolt and a key.
Sometimes a uPVC door mechanism may become stuck because it is unlubricated or something inside has been damaged. If you know what to do, it’s easy to repair.
Prepare for Repairs
uPVC door problems can vary in their severity. If your uPVC door lock is stuck or misaligned, it’s likely that you will be able to fix this problem yourself. However, it is essential to be careful not to do any damage to the lock mechanism as this can make the situation much worse. It is also recommended to avoid using lubricants such as grease or oil as they can actually cause the locking mechanism to become sticky. Instead, you should use graphite or light machine oil as they are safer and won’t harm uPVC.
It can be difficult to remove a uPVC door barrel after it is installed. It is therefore important to carefully consider your actions before you begin. You should hire a locksmith if you are not experienced with this type of repair. They will ensure that the job is done correctly. This will also save you time since they can complete the task quickly and efficiently.
The first step is to remove the screw that holds the barrel in the first place. It will be of a different color to all the screws on the door. It is located on the edging on the inside near the lock faceplate. Once the screw is removed, you will then slide the barrel lock out. Once the lock has been removed, you can then remove the handle.
It is important to know that a locked uPVC can be opened and shut without the handle. The uPVC comes with a built-in security system called multipoint locking. This system comprises of two hooks at the sides and top of the door, as well as a latch or dead bolt in the middle. This allows for an extremely sturdy and secure door.
If you can’t open your uPVC doors, it is likely to be the locking cylinder. The uPVC lock cylinder is equipped with a specific key, which makes it as easy to break or displace like other locks. If you’re not familiar with this type of repair, it’s recommended to get a professional locksmith.
Removal of the Cylinder
The cylinder, also known as the barrel, is a small component in the handle of the handle of a uPVC door that enables you to lock and unlock the door. The pin-based system is utilized and has been used for many years. However, criminals are now targeting it to increase their chances of breaking in. You can increase the security of your home by replacing the cylinder.
First, take the handle from the door by loosening the screws that secure it using a Phillips-head screwdriver. Save the screws so that you are capable of reattaching the handle once the task is complete. Find the pinhole that binds the handle to the interior trim. Find a paper clip or other pin that can be straightened then inserted into the hole. When you turn the handle apply pressure to the pin to release it. Once the pin has been released, you will need to pull the handle towards you to retract the latch.
Once you have loosened the old cylinder, you are able to take it off by hand. Be careful not to damage the threads on either side of the cylinder, or the cam in the middle. If the cylinder is not being able to slide out, it may be being squeezed by the handle furniture or the locking mechanism, and will require loosening so that it can slide out.
If you’re ready to replace your cylinder, select one that has been evaluated by an independent testing organization as meeting minimum standards for antisnap protection and anti-bump. There are a variety of grades of locks that are available. It is essential to know your requirements prior to choosing the right replacement.
Bring the old cylinder to the store if possible so that you can ensure that you’re buying a replacement that matches. There are around 25 different sizes of lock cylinders to choose from and it is therefore essential to measure yours precisely.
Reinstalling the Cylinder
It is possible to replace your locks if not working properly. It is possible to replace your locks for various reasons, including to increase security or meet the requirements of insurance. You may need to change the lock if you’ve lost keys, or you recently relocated. Whatever the reason, replacing your uPVC door lock isn’t difficult and is achievable by anyone with a bit of guidance.
First, ensure that the door is propped or secured to ensure that it does not close during the process. Then, take off the screws that hold the handle in place by using a screwdriver. Remove the screws slowly, or small pieces may fall off. Slide out the interior and exterior handles at the same time after taking off the screws. This is a bit difficult, but it’s essential not to force anything. This could cause damage to the handle mechanism and cause the handles to break.
Locate the cylinder screw on the edge of the door after taking off the handles. It’s usually a large screw that’s in line with the lower end of the cylinder. It should be a different colour from the other screws and easily identifiable. Twist the screw to loosen it, then remove it.
After removing screw, you will be able to see the cylinder. Insert your key and turn it left and right. This will help unlock the cylinder. Once you have it unlocked, you can use a gentle tugging to take the cylinder out of its socket.
Insert the new cylinder into its socket after taking out the old one. If you’re having difficulty trying to pull or wiggle it again. If you’re unable to insert the cylinder into the lock, think about replacing it.
If you’re replacing a euro cylinder ensure that you buy one with anti-snap, anti-bump or protection. These features will improve the security of your home and make it more difficult for criminals to get around the lock.
Reinstalling the Handle
There are a couple of reasons that your uPVC handle could not be functioning properly. Sometimes it’s a simple case of wear and tear but sometimes the problem is more serious. It could be that the cylinder of the lock is damaged and cannot be fixed, in which case it’s time to replace it with a brand new one.
The first thing you have to do is to remove the handle that was previously attached to the door. This isn’t difficult to do and you can usually accomplish this by removing the two fixing screws with the help of a screwdriver. Once the screws are removed there should be nothing holding the handle to the door and it should fall away with little effort.
It’s a good idea to clean the spindle and back plate following the removal of the handle. This will ensure there is no dirt or grime there to cause issues for the new handle. You should also wash the handle with a soft cloth to remove any dust or dirt that could impact the performance of the handle.
Before you put in the new handle, take a look at how it will fit on the door, in the majority of cases, the hook plate and the roller face plate will fit in recesses in the centre lock case so that there is no gap between them. If the handles do not fit properly it can cause an excessive amount of pressure on the centre lock case, and there is the possibility that something could break inside.
Start by sliding more helpful hints into the hole of the exterior handle, then into the hole of the handle inside. It may be necessary to tap the spindle using mallet or hammer to allow it to slide in. Once it’s in position, there is a small bolt of retaining on the outside which you’ll need to tighten. The holes should be lined up and then replace the retaining bolt.