-
alarmgerman6 zveřejnil aktualizaci před 7 měsíci
Reasons to Change Door Lock
There are many reasons to change the door lock, from improving your home’s security to re-decorating your entrance. It is also possible to change locks if your key is stuck inside or is difficult to turn.
DIY novices can easily change their lock. To start, gather the necessary materials.
Take off the lock that was previously used.
Before installing a new lock, it is necessary to remove the old one from the door. This is crucial when you suspect that someone else has access to the home. It could also be an ideal option if you have moved into a house, experienced a break-in or had a roommate move in. It is simpler than you think and can be done in just a few minutes.
Begin by taking off the screws that secure the deadbolt faceplate to the door frame. You will need to remove the screws on both sides of the door in order to remove the faceplate. This will let you see the hidden screws and provide you with a better understanding of how to continue with the rest of steps.
After removing the old faceplate you’ll need to remove the bolt along with the strike plate and strike plate. Use a screwdriver to loosen the bolt and then take it out of the hole in the door. If the bolt is rusted you may need to use a chisel and hammer it. If you use a chisel to remove the bolt, take care to not damage the door frame.
Before you remove the old lock, make sure that your new doorknob and deadbolt fit into the existing holes on the door. A lot of hardware stores and big box stores have a wide selection of locks and can help you choose the right one. If the lock you purchased does not match your door, send it back and ask for help.
While you are removing the lock that was previously in use, look for small notches or depressions in the handle or around the trim. If you can find them, slip a straightened safety pin or a flat screwdriver through them to release the handle and expose screws underneath.
After removing the screw from the handle, you can begin removing the knob. To do this, locate the set screw on the knob’s base and loosen it. Next, you will need to remove the knob from the spindle and carefully remove the spindle from the door.
Install the new lock
It’s a good idea to change the locks on your doors frequently, especially if you have experienced a burglary. Changing the lock is a cheap, easy and effective way to ensure that your home is safe. The majority of people can do it by themselves using a screwdriver, a screwdriver, and some basic directions. You may also want to learn how you can change the lock’s key to ensure that only you hold the key.
You’ll need to purchase an additional lock that has the same keyway as your current lock. You can save money by choosing to change the lock’s key yourself. The majority of locksmiths charge a fee to do this. You can purchase a brand new lock at a hardware store or even online. A standard deadbolt will typically fit on all doors however, you’ll need to measure the area on your door to ensure that it will fit.
Most of the time the lock you purchase will be supplied with the cardboard template that will show the way it will fit on the door. You can use it as a reference when drilling the hole, which is much more convenient than measuring every time. If the template doesn’t line to the hole you intend to drill, you should return it to the hardware store and purchase a different one.
When installing the new lock, you must ensure that it is placed on the right side of the door. You can verify this by inspecting the latch, which ought to be labeled “up” or something similar. Make sure the latch is sitting correctly within the latch plate then secure it with the screws supplied.
If you’re replacing locks on doors It’s important to pay attention to the way it’s operated. Most knob locks are left-handed, but there are some that are right-handed. If you are not paying attention, the knob could be installed on the wrong side of your door, which could make it impossible to lock from the outside or inside.
It is recommended to test the new lock once you finish. You should be able both to lock and unlock the door using keys from inside as well as the outside. If you aren’t satisfied with the results you can contact an expert locksmith to repair it.
Test the lock
A lock that does not open can be a hassle but it can also put your family’s safety at risk. It’s a good thing that it’s simple to fix the majority of issues with door locks by performing a bit of troubleshooting and lubrication. First, make sure that your key is correctly cut and that the lock isn’t soiled or loose. If this doesn’t resolve the issue, try applying lubrication to the door lock actuator using powdered graphite or a silicone-based oil.
Check that the door lock switch, wiring harnesses and the actuator connector are all working properly. Refer to the wiring diagram or manual to determine the color code and the function of the wires for each door lock switch. Then, test the wires using a light or digital meter to determine whether the door lock’s actuator receives power and ground when the switches are activated. If you notice an electric voltage switch on every switch activation, this suggests that the switches are in good condition and it’s most likely the actuator that needs to be replaced.
If the switch appears to work however the actuator does not move when you turn the knob it could be an issue with the actuator itself. The actuator cylinder is equipped with pins that are spring loaded. They prevent the cylinder from moving until the key is inserted which then pushes them upwards to the same height as the key at that location. The cylinder then begins to turn, opening the lock body and opening the handle latch.
If the door lock actuator is still malfunctioning, you can take the switch and wires from the actuator with a small screwdriver to release the locking bolt and separate the plastic cover that houses the electrical connector. Then, disconnect replacement window lock , and let it fall. You should then be able to find the two bolts of 10mm that hold the actuator in place, and remove them. After the actuator has been removed, you will be capable of disconnecting the black electrical connector and pull it out together with the lock and actuator assembly.
Replace the key
If you have an unkeyed deadbolt or door knob if it is not functioning properly, you must either rekey the lock or replace it completely. It’s not too difficult and can save you money. However, before you do this, it’s an excellent idea to have a locksmith examine the locks and look for any problems. This will give you peace of assurance that your home is secure and safe.
Remove the faceplate on the outside of the doorknob/deadbolt. There may be screws holding it in place, then use a screwdriver loosen them and then pull the faceplate away. Next you can use a flat-head screwdriver to remove the interior faceplate. After you have removed the faceplate, you are able to remove the bolt and screw from the lock cylinder.
A locksmith can decide if you need to replace or rekey your lock. They can also advise you about the best security options for your home. They can also make any necessary adjustments to the door or frame to ensure a perfect fit. They also provide a warranty on their work.
If you choose to rekey your lock, you’ll need to purchase an additional key for it. It is essential to select a key that fits well inside the lock. A key that’s not the right size may damage the internal mechanism of a lock and stop it from functioning. To determine the size of a key, insert it into the lock. If the key is flush against the plug, then it’s the right size. If the pins protrude out from the top of the plug, they’re not long.
You may need to replace your door lock for a variety of reasons, such as:
Rekeying a lock can be an option that is less expensive than replacing it if you’re moving into the home of an owner who has passed away or if your keys have been lost. It’s also less costly than a complete replacement. However, there are circumstances where rekeying your existing lock isn’t an option. If the lock has been damaged or jammed repeatedly, for example it could be the right time to replace it.